988K XE Wheel Loader
Cat® Large Wheel Loaders are designed with durability built in, ensuring maximum availability through multiple life cycles. With optimized performance and simplified serviceability, our machines allow you to move more material efficiently and safely at a lower cost per ton.
Introduced in 1963, the 988 has been the industry leader for over 50 years, built on a legacy of reliability, performance, safety, operator comfort, serviceability, and productivity. The 988K XE brings improved sustainability and maximum efficiency to this machine platform.
- Technical Specs
- Net Power
- 541 hp
- Engine Model
- Cat® C18 ACERT™
- Bore
- 5.7 in
- Stroke
- 7.2 in
- Displacement
- 1105 in3
- Rated Speed
- 1,700 rpm
- Net Power – SAE J1349
- 541 hp
- Torque Rise
- 58%
- Emissions
- U.S. EPA Tier 4 Final/EU Stage IV
- Gross Power – ISO 14396
- 580 hp
- Peak Power Speed
- 1,500 rpm
- Peak Power Speed @ 1,500 rpm: Gross – ISO 14396
- 580 hp
- Peak Power Speed @ 1,500 rpm: Gross – SAE J1995
- 588 hp
- Peak Power Speed @ 1,500 rpm: Net Power – SAE J1349
- 541 hp
- Peak Torque @ (speed) – SAE J1995
- 2104 lbf-ft
- Operating Weight
- 116362 lb
- Bucket Capacity Range
- 4.7-13 m3 (6.2-17 yd3)
- Rated Payload – Standard (face material)
- 12.5 tons
- Rated Payload – Standard (loose material)
- 16 tons
- Rated Payload – High Lift (face material)
- 12.5 tons
- Rated Payload – High Lift (loose material)
- 16 tons
- Operating Weight – Standard
- 116362 lb
- Operating Weight – High Lift
- 119618 lb
- Transmission Type
- Cat switched reluctance electric drive
- Forward 1 (virtual)
- 4.3 mph
- Forward 2 (virtual)
- 7 mph
- Forward 3 (virtual)
- 13.8 mph
- Forward 4 (virtual)
- 20 mph
- Reverse 1 (virtual)
- 4.3 mph
- Reverse 2 (virtual)
- 7 mph
- Reverse 3 (virtual)
- 17.5 mph
- Lift/Tilt System Pumps
- Variable displacement piston
- Maximum Flow at 1,400-1,600 rpm
- 153 gal/min
- Lift Cylinder – Bore
- 8.7 in
- Lift Cylinder – Stroke
- 41.3 in
- Tilt Cylinder – Bore
- 8.7 in
- Tilt Cylinder – Stroke
- 27 in
- Lift/Tilt System – Circuit
- EH-Positive Flow Control, Flow Sharing
- Relief Valve Setting – Lift/Tilt
- 4757 psi
- Fuel Tank
- 147 gal
- Transmission
- 16 gal
- Cooling System (jacket water)
- 30 gal
- Cooling Systems (power train)
- 8 gal
- Engine Crankcase
- 16 gal
- Diesel Exhaust Fluid Tank
- 8.7 gal
- Differentials and final drives – front
- 49 gal
- Differentials and final drives – rear
- 49 gal
- Hydraulic System – implement/steering
- 126 gal
- Note
- All non-road Tier 4 Final/Stage IV diesel engines are required to use: – The machine has the flexibility to run on either ultra-low-sulfur diesel fuel (ULSD with 15 ppm of sulfur or less) or up to B20 biodiesel when feedstock meeting ASTM D7467 specific
- Bucket Capacities
- 4.7-13 m3 (6.2-17 yd3)
- Front
- Fixed
- Rear
- Trunnion
- Oscillation Angle
- 13°
- Brakes
- ISO 3450:2011
- Steering System – Circuit
- Pilot, load sensing
- Steering System – Pump
- Piston, variable displacement
- Steering Cut Off Pressure
- 4351 psi
- Maximum Flow @ × 1,400-1,600 rpm
- 71.3 gal/min
- Total Steering Angle
- 86°
- Steering Cycle Time (high idle)
- 3.4 sec
- Steering Cycle Time (low idle)
- 5.6 sec
- Steering
- ISO 5010:2007
- Rackback
- 4.5 Seconds
- Raise
- 8 Seconds
- Dump
- 2.2 Seconds
- Lower Float Down
- 3.5 Seconds
- Total Hydraulic Cycle Time
- 18.2 Seconds
- Operator Sound Level (ISO 6396)
- 72 dB(A)
- Machine Sound Level (ISO 6395)
- 109 dB(A)
- Note
- The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
- Note
- Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
- Note
- The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
- Air Conditioning
- The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
- ROPS/FOPS
- ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards
- Ground to Top of ROPS
- 13.7 ft
- Ground to Top of Exhaust Stacks
- 14.8 ft
- Ground to Top of Hood
- 10.9 ft
- Ground to Bumper Clearance
- 3.1 ft
- Rear Axle Center Line to Bumper
- 10.5 ft
- Front Axle Center Line to Bucket Tip
- 14.7 ft
- Wheel Base
- 14.9 ft
- Maximum Overall Length
- 40.0 ft
- Ground to Lower Hitch Clearance
- 1.9 ft
- Ground to Center of Axles
- 3.2 ft
- Clearance at Maximum Lift
- 11.3 ft
- B-Pin Height at Maximum Lift
- 18.0 ft
- Maximum Overall Height – Bucket Raised
- 24.5 ft
- Reach at Maximum Lift
- 6.8 ft
- Note
- Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.
- Ground to Top of ROPS
- 13.7 ft
- Ground to Top of Exhaust Stacks
- 14.8 ft
- Ground to Top of Hood
- 10.9 ft
- Ground to Bumper Clearance
- 3.1 ft
- Rear Axle Center Line to Bumper
- 10.5 ft
- Front Axle Center Line to Bucket Tip
- 15.9 ft
- Wheel Base
- 14.9 ft
- Maximum Overall Length
- 41.3 ft
- Ground to Lower Hitch Clearance
- 1.9 ft
- Ground to Center of Axles
- 3.2 ft
- Clearance at Maximum Lift
- 12.7 ft
- B-Pin Height at Maximum Lift
- 19.3 ft
- Maximum Overall Height – Bucket Raised
- 25.8 ft
- Reach at Maximum Lift
- 7.0 ft
- Note
- Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.