D5K2 Track-Type Tractor - Puckett Rents

Engine

Engine Model: Cat C4.4 ACERT
Power - Net: 104 hp
Displacement: 269 in3
Bore: 4.13 in
Stroke: 5 in
Rated Net Power @ 2,200 rpm – SAE J1349: 104 hp
Rated Net Power @ 2,200 rpm – ISO 9249/EEC 80/1269: 104 hp
Note: Engine meets Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) emission standards.

Transmission

Drive Pumps: 1
Track Motors: 2
Relief Valve Settings: 7033 psi
Maximum Travel Speed – Forward: 5.6 mph
Maximum Travel Speed – Reverse: 6.2 mph

Weights

Operating Weight - XL: 20313 lb
Operating Weight - LGP: 20992 lb
Operating Weight – LGP, 762 mm/30 in: 21442 lb
Note: Specs are for machine equipped with dozer blade, canopy ROPS, back-up alarm, operator, coolant, lubricants and full fuel tank.

Service Refill Capacities

Fuel Tank: 51.5 gal
Crankcase and Filter: 2.91 gal
Final Drives, XL (each side): 2.6 gal
Final Drives, LGP (each side): 2.6 gal
Cooling System: 5.92 gal
Transmission/Hydraulic Tank: 15.7 gal
Diesel Exhaust Fluid (DEF) Tank: 4.9 gal

Hydraulic Controls

Pump Output: 17.7 gal/min
Relief Valve Settings: 2988 psi

Undercarriage

Shoe Width – XL: 20 in
Shoe Width – LGP: 26 in
Length of Track on Ground – XL: 91 in
Length of Track on Ground – LGP: 91 in
Track Gauge – XL: 63 in
Track Gauge – LGP: 69 in
Ground Contact Area – XL: 3652 in2
Ground Contact Area – LGP: 4726 in2
Ground Pressure – XL: 5.6 psi
Ground Pressure – LGP: 4.5 psi
Ground Contact Area – LGP, 762 mm (30 in): 5514 in2
Ground Pressure – LGP, 762 mm (30 in): 3.93 psi
Shoe Width – LGP, 762 mm (30 in): 30 in
Track Gauge – LGP, 762 mm (30 in): 73.2 in
Number of Rollers (each side): 7
Number of Shoes (each side) – Sealed and Lubricated Track (SALT) Undercarriage: 40
Number of Shoes (each side) – SystemOne Undercarriage: 36
Length of Track on Ground – LGP, 762 mm (30 in): 91 in

Ripper

Type: Parallelogram
Number of Shanks: 3
Height: 6.5 in
Weight: 1222 lb
Maximum Digging Depth: 13.3 in
Maximum Reach at Ground Line: 21.9 in
Maximum Ground Clearance Under Tip: 17.6 in
Overall Width: 67.3 in

Winch

Weight: 1345 lb
Winch Drive: Hydrostatic
Control: Hydraulic
Speed: Variable
Winch Length: 27.76 in
Overall Width: 29.2 in
Drum Diameter: 10 in
Drum Width: 10.8 in
Throat Clearance: 6.75 in
Rope Diameter – recommended: 0.63 in
Rope Diameter – optional: 0.75 in
Drum Capacity – recommended cable: 371 ft
Drum Capacity – optional cable: 256 ft
Maximum Line Pull – bare drum: 40000 lb
Maximum Line Pull – full drum: 25000 lb
Maximum Line Speed – bare drum: 131 ft/min
Maximum Line Speed – full drum: 207 ft/min

Cab

Sound Levels: ISO 6396:2008: 79 dB(A)
Sound Levels: SAE J1166 FEB2008: 79 dB(A)
ROPS: ISO 6396:2008
FOPS: ISO 3449:2005 Level II

Dimensions

Track Gauge – XL: 63 in
Track Gauge – LGP: 68.9 in
Track Gauge – LGP, 770 mm (30 in) shoes: 73.2 in
Width of Tractor (standard shoes, no blade) – XL: 83.1 in
Width of Tractor (standard shoes, no blade) – LGP: 94.9 in
Width of Tractor (standard shoes, no blade) – LGP, 770 mm (30 in) shoes: 103.5 in
Overall Length (with blade) – XL: 170.1 in
Overall Length (with blade) – LGP: 169.1 in
Overall Length (with blade) – LGP, 770 mm (30 in) shoes: 169.1 in
Length of Basic Tractor (without blade) – XL: 128.5 in
Length of Basic Tractor (without blade) – LGP: 128.5 in
Length of Basic Tractor (without blade) – LGP, 770 mm (30 in) shoes: 128.5 in
Tractor Height – XL: 109 in
Tractor Height – LGP: 109 in
Tractor Height – LGP, 770 mm (30 in) shoes: 109 in
Ground Clearance – XL: 13 in
Ground Clearance – LGP: 13 in
Ground Clearance – LGP, 770 mm (30 in) shoes: 13 in
BLADE: Blade Width – XL: 109.5 in
BLADE: Blade Width – Intermediate: 115 in
BLADE: Blade Width – LGP: 126.7 in
BLADE: Blade Height – XL: 42.2 in
BLADE: Blade Height – Intermediate: 39.8 in
BLADE: Blade Height – LGP: 39.8 in
BLADE: Blade Lift Height – XL: 30.2 in
BLADE: Blade Lift Height – Intermediate: 30.2 in
BLADE: Blade Lift Height – LGP: 30.2 in
BLADE: Digging Depth – XL: 23.1 in
BLADE: Digging Depth – Intermediate: 22.5 in
BLADE: Digging Depth – LGP: 22.5 in
BLADE: Blade Cutting Edge Angle, Adjustable – XL: 52° to 58°
BLADE: Blade Cutting Edge Angle, Adjustable – Intermediate: 52° to 58°
BLADE: Blade Cutting Edge Angle, Adjustable – LGP: 52° to 58°
BLADE: Maximum Tilt – XL: 15.8 in
BLADE: Maximum Tilt – Intermediate: 17.6 in
BLADE: Maximum Tilt – LGP: 17.6 in
BLADE: Maximum Angle (either side) – XL: 25°
BLADE: Maximum Angle (either side) – Intermediate: 25°
BLADE: Maximum Angle (either side) – LGP: 25°
BLADE: Blade Width at Maximum Angle – XL: 103.8 in
BLADE: Blade Width at Maximum Angle – Intermediate: 105.1 in
BLADE: Blade Width at Maximum Angle – LGP: 115.8 in
BLADE: Blade Capacity (SAE) – XL: 2.86 yd3
BLADE: Blade Capacity (SAE) – Intermediate: 2.73 yd3
BLADE: Blade Capacity (SAE) – LGP: 3.06 yd3

ELECTRICAL
- Alternator, 12 volt, 120 Amp, heavy duty brushless
- Alarm, backup
- Batteries (2), heavy duty, maintenance free, 2,000 CCA
- Diagnostic connector
- Horn, electric
- Lights, halogen, 2 front and 2 rear
- Starter, electric, 12 volt
OPERATOR STATION
- ROPS/FOPS canopy
- Seat, air suspended, cloth or vinyl
- Seatbelt, retractable 76 mm (3 in)
- Foot pads, dash
- Electronic Monitoring System with: – Gauges for engine coolant temperature, hydraulic oil temperature and fuel level – Travel speed limiter, electronic – Engine RPM and gear display – Hour meter, electric – Engine air cleaner service indicator, electronic – Water-in-fuel indicator, electronic
- Slope Indicate
- Throttle switch, rotary
- Eco mode
- Controls, seat mounted, fore/aft adjustment
- Armrests, adjustable
- Mirror, rearview, inside
- Single pedal combining deceleration and braking functions
- Independent forward/reverse speed settings
- Power port, 12 volt
- Coat hook
- Storage compartment
- Cup holder
- Floor mat, rubber, heavy duty
HYDRAULICS
- Hydraulics, 3 valve
- Load sensing hydraulics
- Single lever, three function control
- Hydraulic pump and oil
- Stable blade control
POWER TRAIN
- Cat C4.4 ACERT diesel engine, turbocharged, Tier 4 Final/Stage IV/Japan 2014 (Tier 4 Final) certified with aftertreatment
- Aftercooler, Air-to-Air (ATAAC)
- Aluminum bar plate cooling system (radiator, power train)
- Air cleaner with precleaner, automatic dust ejection and under-hood intake
- Dual path, closed-loop hydrostatic transmission
- Electric fuel priming pump
- Fuel/water separator
- Automatic Traction Control
UNDERCARRIAGE
- SALT Undercarriage
- 7 roller track frame
- Track rollers, lifetime lubricated
- Carrier rollers
- Track adjusters, hydraulic
- Guards, front/rear guiding
- Master link
OTHER STANDARD EQUIPMENT
- Cat Product Link^™ PL631 Satellite/PL641 Cellular
- C-Frame, VPAT, hydraulic cylinders and lines
- Lockable engine enclosures
- Front pull device
- Rigid drawbar
- Ecology drains (engine, power train and implement oil and engine coolant)
- Scheduled oil sampling ports (engine, power train implement oil)
- Vandalism protection
- Heavy duty crankcase guard
ANTIFREEZE
- Extended life coolant, –37° C (–35° F)

ELECTRICAL
- Integrated four front halogen lights, two rear halogen lights
POWER TRAIN
- Drive, auxiliary
- Installation, winch
UNDERCARRIAGE
- Track Pairs, XL: – Track, 510 mm (20 in) MS SystemOne
- Track Pairs, LGP: – Track, 660 mm (26 in) MS SystemOne – Track, 762 mm (30 in) MS SystemOne
OPERATOR STATION
- Cab with air conditioning*
- Cab, polycarbonate windows and air conditioning*
- Seat, air suspension, choice of: – Vinyl, heated seat with heated controls – Cloth, heated seat with heated controls – Cloth, heated and ventilated seat with heated controls
- Radio, AM/FM, Bluetooth
- Sound suppression
- *Air Conditioning System: The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.6 kg) of refrigerant which has a CO2 equivalent of 2.288 metric tonnes.
HYDRAULICS
- Hydraulics, 4 valve for use with ripper
- Hydraulics, 4 valve for use with winch
GUARDS
- Guard, rear, heavy duty
- Grill, radiator, heavy duty
- Guard, track guiding, center
- Guard, track roller, full length
- Screen, rear, cab
- Screen, side, cab
- Screen, rear, canopy
- Screen, front and doors, canopy
- Sweeps, front
- Sweeps, rear
BLADES
- VPAT XL blade
- VPAT LGP blade
- VPAT Intermediate blade
REAR ATTACHMENTS
- Drawbar, towing
- Mounting, winch
- Ripper, parallelogram, includes three shanks and teeth
REAR ATTACHMENT CONTROL
- Control, ripper
- Control, winch
- Control, ripper and winch
MACHINE CONTROL AND GUIDANCE
- Installation, AccuGrade ready, includes Cat Grade Control Slope Assist
- Power Pitch blade control
STARTING AIDS
- Heater, engine, coolant, 120 volt
- Starting aid, ether
OTHER ATTACHMENTS
- Machine Security System
ANTIFREEZE
- Extended life coolant, –50° C (–58° F)
FIELD INSTALLED ATTACHMENT
- Winch, hydrostatic